Tuesday, December 29, 2020

Shed Arrives and Garage Cleaning Part 5(?)








Not quite what I ordered...I didn't want a floor so I could just drive stuff in and park on the gravel. But I can make this work (will need to make ramp). Also probably will end up making a door since it has a floor now.

I'll also reinforce the sides with concrete blocks or pressure treated this spring so there isn't as much weight canterlivered off the 4x4s in the middle.







Lawn mower looks closer to the rear than it is. There is a good foot plus.

So I'm thinking I'll put a 20" shelf coming off the back wall -- the studs are true 4" dimension, so that will for the most part provide 24" deep shelves. Two 10' long shelves will be quite a bit of storage.

Gas cans can go on the floor in the back. Smaller bottles I'll put along the sides; I can put up some more horizontal 2x4s for shelves and I'm planning to put some paracord with a taught-line hitch to keep bottles from falling over.



Channeling my Mother...cleaning up containers that will be getting moved to the shed.

I figure "bulk" fluids (and gardening stuff) can live out in the shed. Only need a few bottles like brake fluid and oil in the garage to use for a quick top off.



Using brake cleaner to take the word "Gas" off a diesel jug. In front of an open flame. What could go wrong?






This weekend...



So pretty sure I can retire these two yellow racks this weekend. Might move one, other is probably gonna get scrapped.

This will provide a nice space for the Husky tool box to roll into.

Tuesday, December 15, 2020

That's not how this works...

Been having an issue with being able to pump gas at only 2/3rds of a gallon per minute. Since spending 18 minutes at the pump from the normal 1/4 tank its time to refill point is not my idea of fun in the last 6 weeks or so I've only put 30 miles on it.

Little Googling said this is almost always the "Leak Detection Pump" which is a $15 part that takes about 15 minutes to change and most of that is just getting setup and breaking down after changing it.

Couldn't close the door with the small equipment in the garage, but not worth moving it out tonight for this quick project...


The heater did make the rear area noticeably much more comfortable though! It was just about freezing outside.


"Huh, hose is hanging lose, that's not how this works. Looks a bit more..."That's not how ANY of this works!"


Oh well, couple pieces of kindling for the woodstove, new LDP installed, Jeep now fuels normally.


Sunday, December 13, 2020

Cleaning & Organizing the Garage Part 3 of...a continuing story

Worked a couple hours on Saturday, but it was kind of raw so I lost my ambition to go out again after lunch.

Also doesn't appear I took photos Saturday, these are all from Sunday :D

We are however winning the battle. Basically the battle is over, I just have to finish policing the perimeter to finish cleaning/organizing, much in the way ancient warriors would roam over a battlefield after the battle thrusting swords into their enemies to humanely dispatch them.

Continuing the rack reinforced with scrap lumber.




Enough dunnage to make some poorly equipped Rescue-Engines jealous.







Putting fold-down casters on the workbench. Bottoms needed to be 1.4" so I used these as spacer/templates:








And...this is me after I tripped on the forks while trying to walk out the old locker...a couple minutes later I ripped my jeans on the same locker.




Wide, clear shot all the way to the back door-wall!



















Friday, December 11, 2020

Cleaning & Organizing the Garage Part 2 of ... unknown

Monday morning ran up to Putnam to order some 3/4" stone, and picked up a dolly at Tractor Supply to store the dunnage on at least for now (think it will end up in the bottom of one of the rolling racks)




Litte frosty this morning :).

Somehow despite minimum outside world contact, I have a virus. Was running a fever Wednesday night, a bit better Thursday, mostly OK today but still uggh since it's supposed to be a nice weekend with highs around 50.



7 yards, $195 cash.





Cutting some plywood for the flip-down white board idea I have for the house.



Then making a set of wheels for the last rack, unfortunately damaged the rack trying to lift it on. But I have more parts so I'll build a new bottom for the rack tomorrow right on the new base.

Continuing to use up scrap pieces of wood left over from the '17 house rebuild.



Moving the blocks for the new shed base...damn that took all my tractor could -- had to step on the accelerator to get it lifted.